Comtrol AT Commands for SmartACFL Manuale Utente

Doc. No. 100722ANovember 2, 2000AT Commands for SmartSCM,SmartACF, and SmartACFLModemsReference ManualConexant Proprietary Information

Command Reference ManualxConexant100722AThis page is intentionally blank.

Command Reference Manual3-80Conexant100722AIf an AXCELL™ solution is used, a transmit level of -10dBm is required, therefore the following initializat

Command Reference Manual100722AConexant3-81 Table 3-14. Remote Modem Configuration and Resulting Transmit LevelsRemote ModemConfigurationBase Site Con

Command Reference Manual3-82Conexant100722A3.5 RESULT CODESThe modem responds to commands from the DTE and to activity on the line by signaling to the

Command Reference Manual100722AConexant3-83 Table 3-15. Result Code DefinitionsCode Message Meaning+F4 +FCERROR High speed fax data (V.27, V.29, V.33,

Command Reference Manual3-84Conexant100722A Table 3-15. Result Code Definitions (Continued)Code Message Meaning33 FAX A fax modem connection is establ

Command Reference Manual100722AConexant3-85 Table 3-15. Result Code Definitions (Continued)Code Message Meaning136 +MCR: V21 The modem has connected t

Command Reference Manual3-86Conexant100722A Table 3-15. Result Code Definitions (Continued)Code Message Meaning183 CONNECT 33333 The modem has connect

Command Reference Manual100722AConexant4-14. FAX CLASS 1 AND FAX CLASS 1.0 COMMANDS4.1 FAX I/O PROCESSINGThe fax I/O interface supports asynchronous

Command Reference Manual4-2Conexant100722A4.1.4 Fax OriginationOrigination of fax calls is made using the ATD command. Upon completion of the dial fun

Command Reference Manual100722AConexant4-3If the modem detects a receive buffer overflow condition, it concludes that there was an FCS error in that f

Command Reference Manual100722AConexant1-11. INTRODUCTION1.1 OVERVIEWThis manual describes the host command and responses for the following Conexant m

Command Reference Manual4-4Conexant100722A4.2 COMMANDS AND PARAMETERS4.2.1 Mode Entry Commands4.2.1.1 +FCLASS=1 - Select Facsimile Class 1 Mode+FCL

Command Reference Manual100722AConexant4-54.2.2.3 +FTS - Transmit SilenceThis command causes the modem to terminate a transmission and wait for <t

Command Reference Manual4-6Conexant100722A4.2.2.5 +FTM - Transmit FacsimileThis command causes the modem to transmit data using the modulation define

Command Reference Manual100722AConexant4-74.2.2.6 +FRM - Receive FacsimileThis command causes the modem to enter the receiver mode using the modulati

Command Reference Manual4-8Conexant100722A4.2.2.7 +FTH - Transmit Data with HDLC FramingThis command causes the modem to transmit data using HDLC pro

Command Reference Manual100722AConexant4-94.2.2.8 +FRH - Receive Data with HDLC FramingThis command causes the modem to receive frames using HDLC pro

Command Reference Manual4-10Conexant100722A4.2.3 Service Class 1 Parameters4.2.3.1 +FAR - Adaptive Reception Control If Adaptive Reception is enable

Command Reference Manual100722AConexant4-11Syntax+FDD=<value>Defined Values<value> Decimal number corresponding to the selected option. Fo

Command Reference Manual4-12Conexant100722A4.2.3.4 +FIT - DTE Inactivity TimeoutThis command specifies a DTE inactivity timeout value that allows the

Command Reference Manual100722AConexant4-134.2.3.5 +FPR - Fixed DTE RateThis numeric extended-format parameter specifies the data rate at which the m

Command Reference Manual1-2Conexant100722A1.1.4 ConfigurACE II for Windows Utility ProgramThe PC-based ConfigurACE II for Windows utility program all

Command Reference Manual4-14Conexant100722A4.2.3.8 +FMR? - Request Revision IdentificationThis command causes the modem to transmit one or more lines

Command Reference Manual100722AConexant4-15 Table 4-4. Fax Class 1 Calling Sequence (Transmitting a Single Page)DTE Commands Modem Responses Local Mod

Command Reference Manual4-16Conexant100722A Table 4-5. Fax Class 1 Answering Sequence (Receiving a Single Page)DTE Commands Modem Responses Local Mode

Command Reference Manual100722AConexant5-15. FAX CLASS 2 COMMANDSThe Fax Class 2 commands are summarized in Table 5-1.5.1 COMMAND SYNTAX AND GUIDELI

Command Reference Manual5-2Conexant100722A Table 5-1. Fax Class 2 CommandsCommand FunctionService Class ID+FCLASS= Service ClassClass 2 Action Command

Command Reference Manual100722AConexant5-3General Rules1. +Fnnn commands must be entered completely, otherwise an ERROR response is sent.2. All respon

Command Reference Manual5-4Conexant100722A5.1.5 Identification of T.30 OptionsGroup 3 devices negotiate session parameters in DIS, DCS, and DTC frame

Command Reference Manual100722AConexant5-55.3.1 ATD - Originate a CallSyntax: ATD...<CR>The DCE can support a DTE command to originate a call

Command Reference Manual5-6Conexant100722A5.3.3 +FDT - Data TransmissionSyntax: +FDT <CR>The +FDT command prefixes Phase C data transmission. W

Command Reference Manual100722AConexant5-7 Table 5-2. T.30 Session Subparameter CodesLabel Function Value DescriptionVR Vertical Resolution 0 Normal,

Command Reference Manual100722AConexant2-12. SYNTAX AND PROCEDURESThe command and response syntax and procedures generally conform to referenced reco

Command Reference Manual5-8Conexant100722A5.3.4 +FET - Transmit Page PunctuationSyntax: +FET=<ppm>[,<pc>,<bc>,<fc>]DCE respon

Command Reference Manual100722AConexant5-95.3.5 +FDR - Begin or Continue Phase C Receive DataSyntax: +FDR <CR>Default value: 3 seconds in some

Command Reference Manual5-10Conexant100722A5.3.5.2 Continue Document ReceptionThe DTE may issue a +FDR command in Phase D, which releases the post pa

Command Reference Manual100722AConexant5-115.3.7 +FCIG - Set Polling IDThis command allows setting the Local Polling ID string used in a CIG frame. T

Command Reference Manual5-12Conexant100722A Table 5-5. Hang Up Status CodesCode Cause Description0-9 Call Placement and Termination0 Normal and proper

Command Reference Manual100722AConexant5-135.4 SERVICE CLASS 2 DCE RESPONSESThe DCE sends information responses to the DTE as a facsimile session pro

Command Reference Manual5-14Conexant100722A5.4.7 +FPTS: - Receive Page Transfer StatusSyntax: +FPTS:<ppr>, <lc> [,<blc>, <cblc&g

Command Reference Manual100722AConexant5-155.4.11 +FCIG: - Report the Polled Station IDSyntax: +FCIG: “< ID string>” Polled Station IDTh

Command Reference Manual5-16Conexant100722A5.5 SERVICE CLASS 2 PARAMETERSAll Service Class 2 parameters can be read, written, and tested for range of

Command Reference Manual100722AConexant5-175.5.3 +FDCS - Current Session Results ParametersRead syntax: +FDCS?DCE response: +FDCS=VR,BR,WD,LN,DF,EC,B

Command Reference Manual2-2Conexant100722A2.2.4 Repeating a Command LineIf the prefix "A/" or "a/" is received, the modem immedia

Command Reference Manual5-18Conexant100722A5.5.4 +FLID= - Local ID StringWrite syntax: +FLID="<local ID string>"Valid value: 20-chara

Command Reference Manual100722AConexant5-195.5.9 +FAXERR - T.30 Session Error ReportRead syntax: +FAXERR= <table value>, read onlyValid values:

Command Reference Manual5-20Conexant100722A5.5.12 +FBUF? - Buffer SizeRead syntax: +FBUF?DCE response syntax: <bs>, <xoft>, <xont>,

Command Reference Manual100722AConexant5-21 Table 5-6. Send Two Pages, 1-D, No ErrorsDTE Command DCE Response Local DTE Action Remote Station ActionAT

Command Reference Manual5-22Conexant100722A Table 5-7. Receive Two Pages, 1-D Data, No ErrorsDTE Command DCE Response Local DTE Action Remote Station

Command Reference Manual100722AConexant6-16. VOICE COMMANDS6.1 Voice Commands OverviewVoice commands are identified in Table 6-1. Table 6-1. Voice Co

Command Reference Manual6-2Conexant100722A6.1.1 <DLE> Shielded Event Codes Sent to the DTETable 6-2 lists the supported <DLE> shielded co

Command Reference Manual100722AConexant6-36.1.2 <DLE> Shielded Codes Sent to the Modem (DCE)Table 6-3 lists the supported <DLE> shielded

Command Reference Manual6-4Conexant100722A6.2 Voice Commands6.2.1 Configuration Commands6.2.1.1 +FCLASS=8 - Select Voice Mode+FCLASS=8 selects the Vo

Command Reference Manual100722AConexant6-56.2.2 Voice Commands6.2.2.1 +VIP - Voice Initialize All ParametersThis command causes the modem to initiali

Command Reference Manual100722AConexant2-32.4 Extended Syntax Commands2.4.1 Command Naming RulesBoth actions and parameters have names, which are us

Command Reference Manual6-6Conexant100722A6.2.2.3 +VTS - Send Voice Tone(s)This command causes the modem to send DTMF digit or hookflash tones with t

Command Reference Manual100722AConexant6-7Example 1. This example illustrates tone generation without using any null elements. The command example is

Command Reference Manual6-8Conexant100722A6.2.2.4 +VTX - Start Modem Transmit (Playback)This command causes the modem to start the voice transmission

Command Reference Manual100722AConexant6-96.2.2.7 +VIT - Voice Inactivity Timer (DTE/Modem)This command sets the modem’s initial value for the DTE/mo

Command Reference Manual6-10Conexant100722A6.2.2.8 +VLS - Analog Source/Destination SelectionThis command causes the modem to select one or more sour

Command Reference Manual100722AConexant6-11 Table 6-5. +VLS Command OptionsLabel Primitives Description +VTX +VRX +VSP=10 None DCE on-hook. Local phon

Command Reference Manual6-12Conexant100722A Table 6-6. Events Detectable in the Voice Mode per V.253Event Number Event Description Event Reporting0 Ca

Command Reference Manual100722AConexant6-136.2.2.9 +VRA - Ringback Goes Away TimerThis command sets the length of time the modem will wait between ri

Command Reference Manual6-14Conexant100722A6.2.2.11 +VSD - Silence Detection (Quiet and Silence)This command causes the modem to set the silence detec

Command Reference Manual100722AConexant6-156.2.2.12 +VSM - Compression Method Selection This command causes the modem to set the voice compression met

Command Reference Manual2-4Conexant100722A2.4.2.3 Compound ValuesActions may have more than one subparameter associated with them, and parameters may

Command Reference Manual6-16Conexant100722A6.2.2.13 +VTD - Beep Tone Duration TimerThis command causes the modem to set the default DTMF/tone generati

Command Reference Manual100722AConexant6-176.2.2.14 +VDR - Distinctive RingThis command causes the modem to enable or disable reporting of the ring ca

Command Reference Manual6-18Conexant100722A6.2.2.15 +VDT - Control Tone Cadence Reporting***This command is included for compatibility only and has no

Command Reference Manual100722AConexant6-196.2.2.16 +VPR - Select DTE/Modem Interface Rate (Turn Off Autobaud) This command selects the DTE/modem inte

Command Reference Manual6-20Conexant100722A6.2.3 Speakerphone Commands6.2.3.1 +VSP - Speakerphone ON/OFFThis command turns the speakerphone ON or OFF

Command Reference Manual100722AConexant6-216.2.3.3 +VGM - Microphone GainThis command causes the modem to set the microphone gain of the speakerphone

Command Reference Manual6-22Conexant100722AThis page is intentionally blank.

Command Reference Manual100722AConexant7-237. INDEX##UD – Last Call Status Report ... 3-55$$F – FastConnec

Command Reference Manual7-24Conexant100722A+FPOLL - Indicate Polling Request... 5-15+FPR - Fixed DTE Rate...

Command Reference Manual100722AConexant7-25S3 - Carriage Return Character ... 3-66S30 - Disconnect Inactivit

Command Reference Manual100722AConexant2-52.4.4.2 Parameter Set Command SyntaxThe definition of the parameter indicates, for each value, whether the

Command Reference Manual7-26Conexant100722AThis page is intentionally blank.

NOTES

Further [email protected](800) 854-8099 (North America)(949) 483-6996 (International)Printed in USAWorld HeadquartersConexant Systems

Command Reference Manual2-6Conexant100722A2.5 Issuing CommandsAll characters in a command line must be issued at the same data rate, and with the same

Command Reference Manual100722AConexant2-72.7.1 ResponsesThere are two types of responses that may be issued by the modem: information text and result

Command Reference ManualiiConexant100722ARevision Date CommentsA 11/2/2000 Initial release.© 2000, Conexant Systems, Inc.All Rights Reserved.Informati

Command Reference Manual2-8Conexant100722A2.7.3 +<name>: <compound_value>Information Text Formats for Test CommandsIn general, the format

Command Reference Manual100722AConexant3-13. DATA COMMAND SET3.1 COMMAND GUIDELINESThe commands used to control and report modem operation in data mo

Command Reference Manual3-2Conexant100722A3.2.1.2 +FCLASS - Select Active Service ClassThis command selects the active service class (mode).Syntax+FC

Command Reference Manual100722AConexant3-33.2.1.4 +VRID - Report Retrieved Caller ID (CID)This command reports the data associated with the Caller ID

Command Reference Manual3-4Conexant100722A3.2.1.6 -SMS= - Select ModeSelects Data mode, DSVD (digital simultaneous voice and data) mode, or enables a

Command Reference Manual100722AConexant3-53.2.1.7 I - IdentificationThis command causes the modem to reports the requested result according to the co

Command Reference Manual3-6Conexant100722A3.2.1.9 +GMI9 - Request Conexant IdentificationThis command causes the modem to report CONEXANT ACF identif

Command Reference Manual100722AConexant3-73.2.1.12 +GCAP - Request Complete Capabilities ListThis extended-format command causes the modem to transmit

Command Reference Manual3-8Conexant100722A3.2.1.13 +GCI - Country of InstallationThis extended syntax command selects and indicates the country of ins

Command Reference Manual100722AConexant3-93.2.1.14 &F - Restore Factory Configuration (Profile)The modem loads the factory default configuration (

Command Reference Manual100722AConexantiiiContents1. INTRODUCTION ...

Command Reference Manual3-10Conexant100722A3.2.1.17 &W - Store Current ConfigurationSaves the current (active) configuration (profile), including

Command Reference Manual100722AConexant3-113.2.1.20 %8 - Plug and Play Vendor ID and Product NumberSets and stores Vendor ID and product number for se

Command Reference Manual3-12Conexant100722A8. The following messages may occur during the uploading process:Message DescriptionDevice not supported D

Command Reference Manual100722AConexant3-133.2.2.2 Q - Quiet Results Codes ControlThe command enables or disables the sending of result codes to the

Command Reference Manual3-14Conexant100722A3.2.2.5 X - Extended Result CodesThis command selects the subset of the result code messages used by the m

Command Reference Manual100722AConexant3-15 Table 3-1. Result CodesShort Form Long Form n Value in ATXn Command Notes01234+F4+FCERROR xxxxx0 OK xxxxx1

Command Reference Manual3-16Conexant100722A Table 3-1. Result Codes (Continued)Short Form Long Form n Value in ATXn Command Notes0123463 CONNECT 26400

Command Reference Manual100722AConexant3-17 Table 3-1. Result Codes (Continued)Short Form Long Form n Value in ATXn Command Notes01234170 CONNECT 4200

Command Reference Manual3-18Conexant100722A3.2.2.6 &C - RLSD (DCD) OptionThe modem controls the RLSD output in accordance with the parameter supp

Command Reference Manual100722AConexant3-193.2.2.8 &K - Flow ControlThis command defines the DTE/DCE (terminal/modem) flow control mechanism. The

Command Reference ManualivConexant100722A3.2.1.6 -SMS= - Select Mode...

Command Reference Manual3-20Conexant100722A3.2.2.10 &Q - Sync/Async ModeThis command is an extension of the &M command and is used to control

Command Reference Manual100722AConexant3-213.2.2.12 &S - DSR OverrideThis command selects how the modem will control DSR. The parameter value, if

Command Reference Manual3-22Conexant100722A3.2.2.14 +IPR - Fixed DTE RateThis numeric extended-format parameter specifies the data rate at which the m

Command Reference Manual100722AConexant3-233.2.2.15 +IFC - DTE-Modem Local Flow ControlThis extended-format compound parameter controls the operation

Command Reference Manual3-24Conexant100722AReporting Supported Range of Parameter ValuesCommand: +ILRR=?Response: +ILRR: (<value> range)Example:

Command Reference Manual100722AConexant3-25Defined Values<string> Character string corresponding to the selected option(s).0-9 DTMF digits 0 to

Command Reference Manual3-26Conexant100722A3.2.3.2 T - Set Tone Dial DefaultThis command forces DTMF dialing until the next P dial modifier or P comm

Command Reference Manual100722AConexant3-273.2.3.6 O - Return to On-Line Data ModeThis command determines how the modem will enter the on-line data m

Command Reference Manual3-28Conexant100722A3.2.3.8 M - Speaker ControlThis command selects when the speaker will be on or off. The parameter value, i

Command Reference Manual100722AConexant3-293.2.3.10 &P - Select Pulse Dial Make/Break RatioThis command determines the make/break ratio used durin

Command Reference Manual100722AConexantv3.2.5 Error Control Commands ...

Command Reference Manual3-30Conexant100722A3.2.3.12 &V1 - Display Last Connection StatisticsDisplays the last connection statistics in the followi

Command Reference Manual100722AConexant3-313.2.3.13 \V - Single Line Connect Message EnableThis command enables or disables the single line connect me

Command Reference Manual3-32Conexant100722A3.2.3.15 %Q - Report Line Signal QualityReports the line signal quality (DAA dependent). Returns the higher

Command Reference Manual100722AConexant3-333.2.3.18 –PPD= - Extension Pickup Notification through 16550 UARTThe –PPD=1 command allows setting of the D

Command Reference Manual3-34Conexant100722ABehavior in Voice Mode (+FCLASS=8)When in voice mode and an extension is picked-up, a <DLE>P is sent

Command Reference Manual100722AConexant3-35Operation in Voice ModeLine-In-Use (enabled by AT-STE=1, AT-STE=3, AT-STE=5, or AT-STE=7):This feature does

Command Reference Manual3-36Conexant100722AModem is connected in data mode and the LOCAL HANDSET goes off-hookAT-STE=7ATDT555-1212 5 sec delayCONNECTN

Command Reference Manual100722AConexant3-373.2.4 Modulation Control Commands3.2.4.1 +MS - Modulation SelectionThis extended-format compound paramete

Command Reference Manual3-38Conexant100722AReporting Current or Selected ValuesCommand: +MS?Response: +MS: <carrier>,<automode>,<min_tx

Command Reference Manual100722AConexant3-39+MCR: Report SyntaxResponse: +MCR: <carrier><carrier> Alphanumeric code corresponding to the re

Command Reference ManualviConexant100722A3.3.3.25 S28 - Bit Mapped Options Status...

Command Reference Manual3-40Conexant100722A3.2.4.4 %U - Select µ-Law or A-Law Codec TypeThis command selects µ-Law or A-Law codec type for V.90 and K

Command Reference Manual100722AConexant3-413.2.5 Error Control Commands3.2.5.1 +ES - Error Control and Synchronous Mode SelectionThis extended-forma

Command Reference Manual3-42Conexant100722AExamples+ES=6 Enable V.80 Synchronous Access Mode originator.+ES=,,8 Enable V.80 Synchronous Access Mode an

Command Reference Manual100722AConexant3-43Reporting Supported Range of Parameter ValuesCommand: +EB=?Response: +EB: (<break_selection> range),(

Command Reference Manual3-44Conexant100722A3.2.5.5 +ER - Error Control ReportingThis extended-format numeric parameter controls whether or not the ex

Command Reference Manual100722AConexant3-453.2.5.6 +ETBM - Call Termination Buffer ManagementThis extended-format compound parameter controls the han

Command Reference Manual3-46Conexant100722A3.2.5.8 \K - Break ControlControls the response of the modem to a break received from the DTE or the remot

Command Reference Manual100722AConexant3-473.2.5.9 -K - MNP Extended ServicesEnables or disables conversion of a V.42 LAPM connection to an MNP 10 co

Command Reference Manual3-48Conexant100722AReporting Supported Range of Parameter ValuesCommand: +DS=?Response: +DS: (<direction> range),(< c

Command Reference Manual100722AConexant3-493.2.6.3 %C - Enable/Disable Data CompressionEnables or disables data compression negotiation. The modem ca

Command Reference Manual100722AConexantvii4.2.3.7 +FMM? - Request Model Identification ...

Command Reference Manual3-50Conexant100722A3.2.7 V.8/V.8bis Commands3.2.7.1 +A8E - V.8 and V.8bis Operation ControlsThis command is defined for two c

Command Reference Manual100722AConexant3-51Reporting Supported Range of Parameter ValuesCommand: +A8E=?Response: +A8E: (<v8o> range),(<v8a>

Command Reference Manual3-52Conexant100722A3.2.8.1 +ESA - Configure Synchronous Access SubmodeThe operation of the Synchronous Access sub-Mode is con

Command Reference Manual100722AConexant3-53Reporting Selected OptionsThe modem reports the selected options in response to the following command:+ESA?

Command Reference Manual3-54Conexant100722A3.2.8.3 +ITF - Transmit Flow Control ThresholdsThe +ITF command determines the flow control thresholds use

Command Reference Manual100722AConexant3-553.2.9 Diagnostic Commands3.2.9.1 #UD – Last Call Status Report#UD is an action command requesting reportin

Command Reference Manual3-56Conexant100722ACommand SyntaxIn response to this command, the modem will report one or more lines of information text as d

Command Reference Manual100722AConexant3-57 Table 3-3. AT#UD Last Call Status Report FormatKey Value(s) Definition0 2 digits Diagnostic Command Specif

Command Reference Manual3-58Conexant100722A Table 3-4. Call Setup Result CodesCode Definition0 No previous call (modem log has been cleared since any

Command Reference Manual100722AConexant3-59 Table 3-8. gstnModulationSchemeActive from 3.7.2/V.58Value Description0 V.17 (G3 Fax call)1V.212V.223 V.22

Command Reference ManualviiiConexant100722A5.4.12 +FDTC: - Report the Polled Station Capabilities...

Command Reference Manual3-60Conexant100722A Table 3-11. callCleared codes from 3.6.4/V.58-1994Value Description Notes0 CauseUnidentified Call setup is

Command Reference Manual100722AConexant3-61Example Modem Response and UsageExample #UD commend response are shown in Table 3-12. Table 3-12. Completed

Command Reference Manual3-62Conexant100722A3.2.10 Compatibility Commands3.2.10.1 &L - Leased Line OperationThis command requests leased line or di

Command Reference Manual100722AConexant3-633.2.10.4 :E - Compromise Equalizer Enable CommandThis command is included for compatibility only and has no

Command Reference Manual3-64Conexant100722A3.3 S-PARAMETERSThe S-Parameters are summarized in Table 3-13 along with their default values; registers de

Command Reference Manual100722AConexant3-65 Table 3-13. S-Parameter SummaryRegister Function Range Units Saved Default**S0 Rings to Auto-Answer 0-255

Command Reference Manual3-66Conexant100722A3.3.3 S-PARAMETER DEFINITIONS3.3.3.1 S0 - Number of Rings to Auto-AnswerS0 sets the number of the rings re

Command Reference Manual100722AConexant3-673.3.3.7 S6 - Wait Time before Blind Dialing or for Dial ToneS6 operation is country dependent.1. Sets the

Command Reference Manual3-68Conexant100722A3.3.3.12 S11 - DTMF Tone Duration S11 operation is country dependent.1. For US models, S11 sets the duratio

Command Reference Manual100722AConexant3-693.3.3.15 S16 - Test Mode Bit Mapped Options StatusS16 indicates the test in progress status.Default: 0Bit 0

Command Reference Manual100722AConexantixTablesTable 3-1. Result Codes...

Command Reference Manual3-70Conexant100722A3.3.3.19 S22 - Speaker/Results Bit Mapped Options StatusS22 indicates the status of command options.Default

Command Reference Manual100722AConexant3-713.3.3.23 S26 - RTS to CTS Delay S26 sets the time delay, in hundredths of a second, before the modem turns

Command Reference Manual3-72Conexant100722A3.3.3.26 S29 - Flash Dial Modifier TimeS29 sets the length of time, in units of 10 ms, that the modem will

Command Reference Manual100722AConexant3-733.3.3.30 S38 - Delay Before Forced Hang UpS38 specifies the delay between the modem's receipt of the H

Command Reference Manual3-74Conexant100722A3.3.3.33 S41 - General Bit Mapped Options StatusS41 indicates the status of command options.Default: 13 (C3

Command Reference Manual100722AConexant3-753.3.3.36 S86 - Call Failure Reason CodeWhen the modem issues a NO CARRIER result code, a value is written t

Command Reference Manual3-76Conexant100722A3.3.3.37 S91 - PSTN Transmit Attenuation LevelIn non-PCM modes (V.90 or K56flex are PCM modes), S91 sets th

Command Reference Manual100722AConexant3-773.3.3.40 S210 – V.34 Symbol RatesThe bits in this parameter control V.34 symbols rates and enables/disables

Command Reference Manual3-78Conexant100722A3.4 CELLULAR COMMANDSCellular direct connect, supported by portable application modems, allows a direct int

Command Reference Manual100722AConexant3-793.4.2.3 ^T6 - Indicate Status of Cellular PhoneThe status of the cellular phone connected to the modem is